Stylish A3 Moto Guzzi Steam and Falcone poster featuring original artwork by Carl Hunton. Celebrating the age of steam the print commemorates s a time when everything moved more slowly. Equally at home in your workshop or living room, treat yourself to this inspiring and timeless image, or buy a friend the perfect Guzzi gift.

Printed on high quality glossy A3 paper, ready to frame

 More than 5 in stock

Clevis pin used in brake and gear change linkages, wears over time so well worth replacing on high mileage bikes

Replaces Guzzi refs. 95780265, 95780267, 95770265-Z, 95780265-Z. See BRA95227 for retaining split pin

 This part is due back in stock soon, call 01484 841395 to reserve yours

 95770265 GU95770265 95 77 02 65
 9577 0265 9577.0265 95.77.02.65

Pair of adjustable Tommaselli clipons, quality aluminium castings and chrome plated tube

These clip ons pivot on the central bolt to adjust the handlebar angle, pull back angle is adjusted on the fork stanchion clamp. These clip ons are unsuitable for use with the PS12 handlebar master cylinder. Bar ends are held in by a rivet and some modification will be needed if you wish to fit bar end mirrors.

 This part is available by special order, request a quote

Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3, V50 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:

• Polished aluminium clock surround front with 80mm holes for instruments, slotted ignition switch hole and 8mm instrument light holes
• 6 LEDs with chrome bezels (small spade connectors to rear) for indicators, oil, charge system, neutral and high beam warning light
• Polished aluminium instrument surrounds (odometer surround includes hole for reset knob)
• Polished aluminium instrument backs (attach with existing nuts)

Manufactured from 6mm aluminium, this this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives. These kits are often prepared to order so please allow for a couple of days delay before your order is sent.

NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated. Check the depth of your instruments before ordering, this kit is intended for 48mm deep instruments with 60mm stud centres

Instruments with 60 degree or similar angle drives to the rear will require you to enlarge cable cutouts in the plates that make up the rear of the kit

 1 in stock

Clutch cable

 5 in stock

 14093002 GU14093002 14 09 30 02
 1409 3002 1409.3002 14.09.30.02

Clutch cable with adjuster for gearbox end

Note this cable only has a barrel nipple at the gearbox end of the cable

 1 in stock

 17093002 GU17093002 17 09 30 02
 1709 3002 1709.3002 17.09.30.02

Tool for clutch centre gear nut

Half inch socket drive. This is a cheaper aftermarket tool- see TOA14903 for original factory item

 This part is due back in stock soon, call 01484 841395 to reserve yours

 14912603 GU14912603 14 91 26 03
 1491 2603 1491.2603 14.91.26.03

Factory tool for clutch centre gear nut, this is a superior design tool intended for repeated use

Designed to fit the original factory spec nut- this may not fit some aftermarket items. See TOA14651 for cheaper aftermarket tool

 This part is available by special order, request a quote

 14912603 GU14912603 14 91 26 03
 1491 2603 1491.2603 14.91.26.03

Original type clutch friction plate for big twins

2 plates required per clutch overhaul- thicker side of each plate should face transmission. Also check your intermediate plate 12082300. This has shallower splines than the Spada 3 on plates. These are the best fit if you still have the original shallow spline clutch hub. Also known as Guzzi ref. 12084400

 This part is due back in stock soon, call 01484 841395 to reserve yours

28084460-z 28084460 GU28084460 28 08 44 60
 2808 4460 2808.4460 28.08.44.60

Shallow splined Newfren clutch friction plate for big twins with old shallow splined clutch centre

2 plates required per clutch overhaul- thicker side of each plate should face transmission. Also check your intermediate plate 12082300. This has shallower splines than the Spada 3 on plates. These are the best fit if you still have the original shallow spline clutch hub

 This part is available by special order, request a quote

28084460-z 28084460 GU28084460 28 08 44 60
 2808 4460 2808.4460 28.08.44.60